Does It Matter Which Sata6g Port Is Used First

Two intel six gig ports and four intel 3G ports and two acmedia or other 3 party Sata chipset. On your board all the ports are the same so it doesnt matter other than drive order.

Does It Matter Which Sata Port You Use Pc Guide 101

These days however all of the SATA.

. So you want your primary disk drive to be connected to port 0. Its essentially been replaced by M2. Only thing I know for sure about that mobo.

The drive uses SATA protocol so install in slot M2 1 and SATA6G_1 port will be disabled so any other SSDs or HHDs cannot use that port. On some cheap motherboards there may be only one six gig port or just four 3G ports. If the SATA ports are the same speeds it doesnt really matter.

You can continue to use SATA port 1 with this setting. And you are not an idiot if your smart enough to ask for answers to the questions you have we all. It will boot from the first disk it finds with a valid partition map and a partition marked as being bootable.

While the official SATA-IO documentation states that there is no difference between SATA 3Gbs and SATA 6Gbs cables there were still some people that insisted that you needed a SATA. SATAExpress is a very fast SATA standard but I highly doubt you have hardware compatible with it. Ssd and hard drives should start on port 0 of the 6g controller.

All You Need To Know About The Sata Interface Delkin Devices Before working inside your computer. The setting is intentionally incomplete allowing the gaps to be filled by imported or homebrew content. On amd mb there may be only two sets the amd 6g and 3G.

It shouldnt matter which theyre plugged in to since youre using a PCIe NVMe based card in the M2 slot. As the previous poster mentions if you are using an M2 drive in the first slot the BIOS sets it automatically to PCI Express mode which is what you want. You would want any SSDs on the 6Gbs ports.

On 9122018 at 856 PM Spotty said. If some of them are faster 60 vs 3015 then you will want your main drive and SSDs in those slots. The other SSD was connected to the SATA-1 port.

On some boards there are SATA 3Gbs ports and SATA 6Gbs ports. Otherwise it wont matter. My motherboard model is H170-PRO as its manufacturer is ASUSTeK COMPUTER INC.

Afterall moving to an authentic SATA 6Gbs cable cleared up our problems the first time right. It really doesnt matter. When you boot your computer the BIOS will look at the disk connected to SATA port 0 first then SATA port 2 etc.

So what you have planed will be fine as long as the ssd is in. Answer 1 of 7. It might give you a couple of percentage points more in.

At the time the magic of an SSD wasnt necessarily that it could shoot dizzying amounts of data through your SATA ports although they could. Thanks I noticed that note. When PCIEX16_ 3 is populated SATA6G_12 and SATA6G_34 will be disbabled.

Lets first say that when we started this we were absolutely sure wed see a difference. Doesnt really matter which port is used while cloning though. And thus if you dont have any m2 drives it doesnt matter at all.

Ok your ports are 1 2 - it does not really matter as you can set them in bios. The manual says use SATA0 and SATA1 for hard drives but SATA1. If you manually tell the BIOS to run the M2 drive in SATA mode instead then you lose SATA port 1.

SATA6G_E12 cannot support RAID 01510. Previously motherboards included old SATA versions and new the old types were slower and only really useful for stuff such as DVD drives which couldnt readwrite faster anyway. Typically the first set of ports are on on the Intel controller which unless you want RAID will be fine.

Nope They should all run fine. The red ones are Jmcron they are not as good performance wise or user freindly wise I use them but only for CDDVD drives for 1 X25 use port 0 it will be the port closet to the board and the two red ports It will not matter if your just running the drive but will matter if you use the Firmware update program. Cd roms on any of the 3G ports.

All of your ports will have the same speed. Basically an m2 sata drive in the second m2 slot disables sata port 3. Dont think Ive any m2 drives.

When SATA 6Gbs drives were first launched there was a lot of confusion over whether or not you needed a special cable in order to get the full speed benefit of SATA 6Gbs. And an m2 pcie drive in the second m2 disables the last pcie slot. Sata6G 12 are ports 1.

Id use SATA0 for the boot drive anything else doesnt matter. Windows 7 was installed first and in the SSD thats connected to the SATA-0 port. Does it matter which SATA port I connect a second hard drive to on a Dimension 9200.

The manual sometimes says use port x for SSDOS but if it doesnt say that youre good with any of them. That can be changed in a BIOS setting. Realistically I doubt you will see much difference between the ports as the MX500 is designed around 6Gbitsec.

But if you want to go in sequential order SATA ports should be listed on the MB from 1 to whatever many ports there are so I guess set your system HD to the first one and the rest use them in whichever order. Without the manual Im not 100 sure but use 1. And then it handed over its first-generation X25-Ms.

Its only when the M2 slot is running in SATA mode SATA based M2 SSDs that 2 of the SATA ports SATA6G_1 SATA6G_2 are disabled. Probably does not matter Id put it into SATA6G_3 as SATA6G_5 and SATA6G_6 MAY be using different controller.

Does It Matter Which Sata Port You Use Pc Guide 101

Does It Matter Which Sata Port You Use Pc Guide 101

Does It Matter Which Sata Port You Use Pc Guide 101